• Trang chủ > Tin tức > Tin tức ngành> Zonal Architecture Wire Harness Design: A Practical Sourcing Guide

    Zonal Architecture Wire Harness Design: A Practical Sourcing Guide

    Time : November 21, 2026 Lượt xem: 9

    Mục lục

      Quick answer: Zonal architecture groups vehicle electrical connections by physical location. For wire harness sourcing, the result is a combination of local branches, zone power feeds and communication links. A useful quotation must define each interface, its electrical requirements and its verification plan—not simply promise a lighter harness.

      This guide explains the design changes and provides an engineering discussion checklist for buyers sourcing automotive cable assemblies. It is general guidance; the vehicle manufacturer’s approved drawings and validation requirements govern each project.

      What changes when a vehicle adopts zonal architecture?

      In a function-based electrical layout, related systems can have wiring spread across the vehicle. A zonal approach connects nearby devices to a local zone controller, which communicates with other controllers and central computing resources. Real vehicles may combine domain and zonal elements rather than follow a single pure architecture.

      Texas Instruments describes zone gateways that consolidate local data and distribute power within a zone. This arrangement can reduce long power runs compared with centralized distribution. See its white paper on zone architectures. That potential does not establish a universal percentage reduction for an individual harness.

      Three interfaces to define before requesting a quote

      1. Local device branches

      List the sensors, actuators and other loads connected to each zone. Provide connector part numbers, cavity assignments, routing dimensions, mounting points and service access. A short branch can still fail if it is pulled tight at a connector or routed across a sharp edge. Specify tolerances around the installed route, including the service loop and strain-relief arrangement.

      2. Zone power feeds

      Document the normal operating current, transient load profile, allowable voltage drop, ambient conditions and protection strategy. The power feed and the local branches need coordinated requirements. Do not select a conductor from nominal current alone: bundling, terminal temperature limits, routing and fault-clearing behavior can affect the final design.

      onsemi’s zonal architecture overview describes power distribution from a low-voltage battery or the high-voltage-to-low-voltage converter toward individual vehicle zones. The harness quotation should identify the actual supply arrangement selected for the vehicle, including return paths and any redundant circuits.

      3. Communication links between modules

      Identify the required network and approved cable-and-connector system. Ethernet, CAN and LIN connections have different physical-layer requirements; they are not interchangeable. Provide the permitted length, connector transitions, shielding arrangement where applicable and the system owner’s acceptance criteria. A continuity test confirms connection mapping but does not establish high-speed link performance.

      Does 48 V automatically mean a thinner wire?

      No. Raising voltage can reduce current for the same delivered power, but the final conductor size still needs an electrical and thermal assessment. Zonal architecture does not require every circuit to operate at 48 V; mixed-voltage designs are possible.

      Illustrative calculation: For an ideal 240 W load, I = P/V gives 20 A at 12 V and 5 A at 48 V. If the wire resistance stayed unchanged, I²R loss would be one-sixteenth. This comparison excludes conversion losses and operating-voltage variation. If a thinner wire is selected, its resistance changes, so that loss ratio no longer directly describes the redesigned circuit.

      TI’s 48 V automotive resources discuss power distribution and conversion building blocks. Neither a voltage increase nor a zone controller replaces the need to validate connector ratings, conductor temperature and circuit protection for the chosen installation.

      A supplier checklist for zonal wire harness quotations

      The following checklist is an engineering starting point, not a certification or a substitute for the customer’s drawing package.

      Quotation item Information to request Why it matters
      Zone boundaries A connection list showing which devices belong to each module. Prevents omitted branches and unclear interface responsibility.
      Routing and dimensions A controlled drawing with branch lengths, tolerances, clips and installation constraints. Makes competing quotations comparable.
      Wire selection Conductor material, cross-section, insulation designation and approved alternatives. Prevents silent substitutions based only on nominal size.
      Connectors and terminals Manufacturer part numbers, mating references, sealing parts and cavity allocation. Defines the actual interface rather than a generic connector description.
      Power protection Customer-approved overload and short-circuit requirements for each protected circuit. Connects wire selection to the intended fault response.
      Data-link construction Approved cable type, network requirements and shield-termination details where required. Separates connection checks from signal-performance verification.
      Production controls Specified crimp tooling, inspection criteria and material or lot traceability. Supports repeatable builds and investigation of nonconforming parts.
      Validation scope A test matrix naming the responsible party, test conditions and pass/fail criteria. Distinguishes routine production tests from design qualification.

      How to compare weight and cost claims fairly

      Ask for the baseline before comparing a savings claim. Does the quoted mass include terminals, housings, seals, conduit, clips and protective sleeves? Is the comparison for one zone module or the complete vehicle? Are the routes and optional equipment identical?

      A shorter route can reduce conductor use while additional connectors or protection components add mass and assembly work elsewhere. Compare a controlled bill of materials and routing revision. Keep prototype tooling, qualification work, recurring unit cost and logistics as separate quotation items.

      Build the verification plan before the prototype

      Prepare a matrix covering connection mapping, visual workmanship and the project-specific electrical, mechanical and environmental requirements. Define how samples are identified, which drawing revision they represent and how deviations are recorded.

      Use continuity and pin-map checks to verify intended connections. Where required by the design, agree insulation resistance, dielectric testing, pull testing, sealing checks or network measurements with the responsible engineering team. Test voltages and methods must suit the assembly; sensitive electronics may require isolation or a different test sequence.

      Close the loop after installation. Confirm connector access, clip position, strain relief and clearance from heat or movement. Record any routing change in the drawing before approving the next build.

      Frequently asked questions

      Does zonal architecture eliminate the wire harness?

      No. It reorganizes power and signal connections. Local devices still need physical interfaces, and zone controllers still need power and communication paths.

      Can a supplier guarantee a fixed weight saving?

      A meaningful commitment needs a defined baseline, installation route, bill of materials and scope. A percentage without those inputs is insufficient for sourcing approval.

      Is every zonal harness a high-voltage harness?

      No. Zone-control wiring commonly concerns the vehicle’s low-voltage electrical system. EV traction wiring has separate requirements. State the voltage class and circuit purpose for every assembly.

      What should a buyer send with an RFQ?

      Provide the drawing revision, connection list, approved components, quantities, operating environment, packaging needs and required validation scope. Identify open engineering decisions so the quotation can state its assumptions.

      Does passing continuity testing prove the assembly is automotive-qualified?

      No. Continuity verifies a limited set of electrical connections. Qualification depends on the customer-approved component, assembly and system validation requirements.

      Discuss your automotive harness project with Songyuan

      Explore our automotive wiring harness range and PEU wiring harness product. For a project discussion, send Songyuan your drawings and application requirements. Ask for component availability, build assumptions and test scope to be stated in the quotation; project-specific capability and delivery timing need confirmation.

      Sources and scope

      The sourcing checklist and calculation above are editorial guidance. They do not assert an OEM project result, certification, independent engineering review or guaranteed performance for a Songyuan product.

      tin tức liên quan
      Trang chủ
             
      WhatsApp
      E-mail
      Liên hệ